![]() ![]() This is a DIY project and will stay as it is. ![]() I am too dumb to build an USBsamurai by myself.F.A.Q.įor many reasons I strongly recommend the C-U0012! Regarding munifying, I usually download it from Github, install golang, libusb and then compile it with “go build”. Moreover, either setup all software on a Kali VM (which is confirmed running all fine) or use sudo to run on your preferred Linux OS. IMPORTANT!!! Be sure you have ONLY that Logitech dongle connected on your computer!! Otherwise, run a Kali VM and attach to it ONLY the C-U00xx you wanna flash/pair! Voila’! You got your remote shell on an Air-Gapped machine!. ![]() Type “ cover_channel connect XX:XX:XX:XX:XX ”.30 seconds for the agent to be fully injected. First deploy the PoSH agent with “ covert_channel deploy XX:XX:XX:XX:XX ”.Start payload injection at your will with “ inject execute”.Tell LOGITACker to use that specific USBsamurai (i.e.Load a paired USBsamurai from Flash, if not yet loaded (i.e.Set the proper workmode on LOGITacker, if not set yet (i.e.Of course you can load multiple USBsamurai! To do that you need to type the following commandĪnd pick the right address of that specific dongle. IMPORTANT!: Every-time you will turn-on LOGITAcker you will have to load from the flash the pairing data of the very specific USBsamurai you wanna use. Once saved in the flash, try to load it again. Script press GUI r script delay 500 script string iexplore -k script delay 200 script press RETURN script store wannacry Simple, connect to LOGITacker over serial and type something as follow. How to create a script and automatically load at startup: For an USBsamurai based on C-U0012 (w/ LIGHTSPEED fw) you need to setup LOGITacker workmode to lightspeed.For an USBsamurai based on C-U0007 (w/ G700 fw) you need to setup LOGITacker workmode to g700.Working modes ( This is mandatory to get everything working properly!!!) : įirst of all, I assume you already flash the latest release of it in one of the compatible hardware. Here we need to split the topic in few points, and I won’t go that deep since there is plenty of documentation in its Github’s repo. IMPORTANT! Before starting be sure you know what you are doing and have all your tools around! But will be discussed in details later on in this article. Where do you get the LIGHTSPEED firmware? Either on Logitech’s Github or HERE. C-U0008/0012) typing speed could be also reduced to 30 seconds with a LIGHTSPEED firmware. :) Check below for the detailed instructions.Īs for TI receivers (i.e. Luckily, It happens I have a G700 firmware available HERE. How we can improve C-U0007 speed? You need to buy an old G700 mouse and dump with munifying its firmware and then flash all the C-U0007 you want. *In case you want more privacy while injecting payloads… I recommend to use the slightly more expensive C-U0012 which has encryption enabled. C-U0007), this could be reduced to 30 seconds if a G700 firmware is used, but injection is always unencrypted* (meaning everybody else could inject to, as G700 accepts plain injection). Which, despite being typed on a stealthy way, is not optimal.įor Unifying receivers with a Nordic chipset (i.e. C-U0007), typing out the Air-gap Bypass Client takes aprox. Simple, for keystroke injection, the receiver model matters, as typing speed depends on this. C-U0012 Unifying Dongle How to Flash the C-U0007 with the G700 firmware to achieve better performances and get the Air-Gap Bypass feature:įirst of all, why do we need to flash the G700 firmware on the C-U0007? ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |